Motorola Photon 4G :: 'Violation Of Security Policy' WiFi Or PPTP
Sep 5, 2011
This may or may not be related to wifi connectivity issues noted in other threads. Blackberry 8350i smartphones using the same wireless configuations operate without generating errors.The direct errors can be produced by either Photon smartphone: [code]" RSB1 Enforcing Default Security Policy.After being installed according to the Installation Documentation (refer to DO1 in the Baseline module),the Candidate Firewall Product must immediately enforce the Default Security Policy as defined below:Traffic Denied Inbound - The Candidate Firewall Product must drop or deny non-Remote Administration related access requests from public network clients directed to:
1. Private network hosts;
2. Service network hosts;
3. The Candidate Firewall Product itself...."
I have two wireless routers (different SSIDs and channels), a Netgear WPNT834 Rangemax 240 (IP4) and a Netgear WNDR4000 (IP4/IP6).When both are setup in AP configuration, both produce the "violation of security policy" errors.If the WNDR4000 is setup as a wireless router with IP4 setup and IP6 set as automatic the errors are produced as usual by the photons.If the IP6 in the WNDR4000 is disabled in wireless router configuation the errors stop.There seems to be no duplicate packets presented to the Motorla Mobilty R910 router.Maybe these "violation of security policy" packets are not created properly or duplicated by the photon's IP6 drivers when dealing with IP4 only wireless routers?Perhaps this is the source of the photons wireless instability noted by many others?Of course these packet problems would ideally be confirmed by others with even better equipment.
View 2 Replies
ADVERTISEMENT
Aug 30, 2011
I am able to use PPTP VPN over 4G without problems. However if I disconnect. Then turn off 4G. Wait a minute or two or even overnight. Then try to connect the PPTP VPN over 3G it fails. So, does PPTP VPN work over Sprint 3G?Initial research: I have read on some old posts that VPN over Sprint 3G is not supported from smart phones, only wireless modems. Some of the VPN problems were also caused by earlier versions of the android linux. Is it possible to use VPN over Sprint 3G from a Photon? If not does PPTP VPN work on other Sprint phones?
View 3 Replies
View Related
Jun 23, 2015
Got a message this morning that there was a security policy update to download. I'm thinking this is to resolve the keyboard issue? Am I able to take the update at all if I'm rooted (but stock)? Will it break anything? Sprint version, so I don't think it's the 5.1.1 update.
View 8 Replies
View Related
Oct 16, 2011
I like to keep wifi active all the time when at home. So, I set the wifi sleep policy to NEVER (advanced wifi option) but...when the screen goes dark, my wifi immediately disconnects. I confirmed this by pinging the ip address of my Droid x2 from a computer. When the screen is lit the wifi goes active and I get a reply to the pings. When the screen goes dark after the 30 sec screen timeout, the pings no longer work, and I am no longer connected via wifi or 3g. In fact, there is no data connection at all.
I even tried the other wifi sleep policy settings, but they don't seem to change a thing. Bottom line is when I am connected to wifi and the screen goes dark, I loose all data connectivity & loose the ability to receive gmail and Touchdown email notifications.
I just recevice the X2, upgraded from the Droid X. I used to have a Droid X and the "never" sleep policy option worked just perfectly. Why is it not working on the X2? I am running 2.3.4.
View 15 Replies
View Related
Jan 6, 2010
I recently got an LG Xenon GR500 through ROGERS however I cannot install my own apps or games, ringtones etc as Rogers has locked all these features in the hopes that people will then buy from them. I was wondering if unlocking the phone will remove Rogers' Security policy from my phone so I can then do all this stuff. Is there anybody that has tried something like this before, perhaps even on a different phone?
View 1 Replies
View Related
Oct 3, 2011
I have set my Wifi Sleep Policy to "Never", because i like to strem my music with DLNA App to my HiFi, and i'm also downloading with Torrent App some TV Shows.Music Streamin works fine with Original DLNA app from Atrix, but only until the Display turns off. Then it stoped everything.I also set DLNA to never sleep and i also tried Battery set to "Performace". It simply doesn't work.With Torrent app from the Market also the same problem. I tried several apps. After the display is turned off there are no transfers.I own also Samsung Galaxy Tablet. With this device i don't have any of these problems.The funny thing is that the original DLNA app from Atrix simply don't stream the music after the display turnes off.
View 2 Replies
View Related
Aug 26, 2010
I needed to clear the IT policy from my BB Bold. I followed the instructions:
- backup
- wipe handheld
- replace policy.bin file
- restore
The phone works just fine. The policy appears to be gone, and I can set the security options as I want. However, when I start my Blackberry Desktop, I get an error saying "error reading policy file. Please contact your Administrator". Any idea what the issue is and how to correct it?
View 4 Replies
View Related
Mar 9, 2011
I bought a BB 9800 Torch n it was locked and I managed to unlock the phone for calls, txt messages but BB messenger, Face Book, Twiter are not working the message appearing ( This application has been disabled by IT policy).
View 9 Replies
View Related
Sep 20, 2012
I have my device set for Wi-Fi to stay on only when plugged in (Settings > WiFi > Advanced > Keep Wi-Fi on during sleep). (see pic #1) The goal being when the device is not in use the WiFi turns off to conserve battery and when I wake up the unit it automatically turns WiFi back on, scans for networks and auto connects to my preferred WiFi networks.Everything works great until the unit sleeps. When I wake it up WiFi never connects. WiFi is set to ON when you look under Settings but when you select the WiFi menu all it says is "Searching for WiFi networks" (see pic #2). Please don't tell me that there aren't any WiFi networks within range because I'm sitting 3 feet from mine now. I also gave it a good 10 minutes to scan, and even pushed the SCAN button.
The only way I can get WiFi to actually work is to turn off the WiFi then turn it back on. Only then will it actually scan for and connect to WiFi networks (see pic #3). Everything will work as intended until the unit goes back to sleep.It's not the end of the world but it is frustrating given it's a new phone. I can make it work by cycling the WiFi off & on or by changing the settings for WiFi to always stay on (even when sleeping).I already did a factory reset and did not install any other apps, not even system app updates found in the Play/Market.
View 2 Replies
View Related
Jan 1, 2012
My phone suddenly got restarted when i was in wifi connection. After restart, i get "wifi error" message when trying to connect to my wifi.System version - 45.3.6.MB855.Sprint.en.USBuild Number - 4.5.1A-1_SUN-198_6Tried the following, but none worked :(1. Go to airplane mode, forget the wifi network and restart.2. Go to airplane mode, restart. Switch off the airplane mode and restart.
View 4 Replies
View Related
Sep 8, 2011
I'm having this weird issue with WhatsApp with my Photon. It only works on wifi, but when connected through 3G UMTS, it says that there is not internet connection, and I'm pretty sure that there is internet connection available. Actually all other applications (Gtalk, Gmail, Browser, etc) are working fine with the 3G data, this is only happening with WhatsApp.
View 5 Replies
View Related
Feb 2, 2012
Since the last update with 4G turned on it shows connected in the notification area even though it is not connected and wifi is connected.
View 15 Replies
View Related
Aug 24, 2011
why wifi was working when the update came down and now it refuses to work? I press the toggle to turn on wifi and I am greeted with "error" in little letters under it.you managed to actually make this useless to me down here! B/C the SIM/APN issue was screwed up I was running my data over a mifi type device down here and now you've made the phone useless!and yes I have now rebooted multiple times after the "must have update" that you forced onto my phone with no warning?
View 15 Replies
View Related
Nov 2, 2011
I used the Moto software to back up my phone yesterday, and since then it won't connect to wi-fi. It finds the signal, starts looking for an IP address, then stips the process. I've tried to turn off 3G and 4G, together and in combinations, updated PRL and profile, but to no avail. Even rebooted the router to make sure something wasn't wrong with it and other devices in the house are working just fine. Not sure if this has anything to do with the backup, but it's a problem I've never had before.
View 6 Replies
View Related
Sep 16, 2011
I just installed the 45.2.7.MB855 update on my Sprint Photon 4G and now both my WiFi and 4G wont turn on. When I go into Wireless & Network Settings and click on WiFi, all it says is Error and nothing happens. When I try to turn in 4G nothing seems to happen.I am able to turn on Bluetooth and 3G took a couple of Profile updates to get working.
View 8 Replies
View Related
Oct 13, 2011
It broke my phone... I can no longer turn on 4G or turn on the wireless. I found this out within 5 minutes of installing the update.I have not played with the phone enough to find out if it broke anything else. I press the buttons, or icons on the screen to turn these on, and they do nothing. I can hold on the icon and it will allow you to move them though
View 15 Replies
View Related
Nov 26, 2012
I've had this Photon Q lte for 3 weeks, and the battery is ridiculous. I have to charge it at least twice a day, even when I'm not using it for anything. Wifi is always off because I don't need it, but sometimes my battery analysis lists wifi as having used almost 25% of the power! I can't find anywhere else to turn it off. I'm having serious regrets about being stuck with this thing for 2 years!
View 2 Replies
View Related
Oct 18, 2011
So about half an hr ago i got a prompt to update my phone to (45.2.5.en.US) and it installed successfully, then I had problems with WiFi and so restarted my phone, now when I try to access any app that requires WiFi it seems as though it doesn't read it. The browser works fine, but any other app doesn't.
View 2 Replies
View Related
Sep 22, 2011
My Photon sees the network and allows me to enter a password, but then attempts to connect, scans again and boots me out. The message it says that the network is disabled.
View 2 Replies
View Related
Oct 2, 2011
I am having problems connecting to my home network. The phones wifi turns on fine, gets an IP address and looks fine. However, the wifi and phone strength meters grey out and there is no connectivity to the internet on the phone. The wifi network is WPA protected.The phone worked fine on a different, unprotected, network I found up the street.I have a cliq that works fine on my network.I have tried powering off and powering off in airplane mode, neither of which make a difference.
View 3 Replies
View Related
Sep 19, 2011
I have several wifi devices (laptops / tablets) that connect without a problem to my home WPA2 secured wifi network.The photon detects this network and will connect to my home network, BUT ----Implied Profanity Removed---- there are many occassions when it will try to locate the router and try to connect but always loops with "obtaining IP address" -The only solution I have for the photon to connect is by manually rebooting or turning off/on the router, disabling photon wifi > re-enable photon wifi > select my home network and it will connectI have a static IP address for my main router connection and have assigned a DHCP range from : 192.168.31 - 192.168.254 with a lease expiry of 24 hours.
The router and my bandwidth (24mb down / 1.5mb up) has been going strong for a few years.What setting am I missing here or need to modify? I never had to reboot or reset my other wifi devices to ever connect, and I just changed the DHCP range to the above again today. I had a channel setting of "6" and changed it to "11" now also...Once the wifi is connected to the photon, it will stay connected for the most part, but if I leave the home or perhaps overnight the wifi gets disconnected resulting in me having to reboot the router, disable photon wifi, re-enable photon wifi for it to connect
View 15 Replies
View Related
Aug 30, 2011
Have noticed that my Photon can't seem to hold a WIFI connection. I can be sitting right next to my router, and it will drop the connection and start scanning again. Have noticed the same thing with other wifi connections at work. Also the WIFI connection sometimes goes dormant/gray and won't wake up on its own. The only solution is to turn the wifi connection off/on, or to cycle the power on the router. Not sure if its a setting that kills the connection after a period of inactivity, have looked in the settings but can't seem to find anything. I have had this problem pre and post update, but am frustrated as I've just passed my 30 days to return the phone easily if something is wrong with the phone.
View 3 Replies
View Related
Sep 15, 2011
Is there any way to change the preferred order of WiFi networks? My office has two WiFi networks, one for my office and one for the conference room down the hall. When I added the network for the conference room I found that when I'm in the office the phone keeps connecting to it, even though the signal is much weaker than the office network. I ended up just removing it from the list, however, when I'm in the conference room I have to re-add it, which is a pain because there's a long password. On my Windows laptop it's easy to just change the order and it will connect to the one closest to the top of the list, but I can't find anything like that on my Photon. It seems like it would be something pretty simple that would have been built-in.
View 3 Replies
View Related
Sep 28, 2011
Last night when I turned on my wifi at home, the wifi and phone signal bars appeared but were gray and I had no internet/data connection. I checked the wifi settings which indicated I was connected with good to excellent signal. Toggled the Wifi on and off several times, and turned phone on and off, which did not work. Went into wifi settings and told it to forget settings and reconnected, same result. When I turn off wifi, 3G appears and data connection is restored. Left the phone on in the media dock all night, and this morning when I turned on wifi, all was fine. What does gray signal bar mean?
View 1 Replies
View Related
Oct 4, 2012
The wifi antenna regularly turning itself on to check for signal is a cool feature, but it opens over running applications causing the background application to freeze (most notable with my flashlight app) or run without me and not accept any input (many games). Set this to only request to connect to a network if no other apps are running.
View 5 Replies
View Related
Jan 24, 2012
using Photon 4G with Airtel prepaid sim with system version 45.3.6.MB855.Sprint.en, Whenever I run short codes (USSD codes) like *123# to check my prepaid GSM balance or interact with service provider by *121# it takes long time showing USSD code running.. and after few mins either shows MMI successfully complete or MMI failed but doesnt actually show the text which is shown in my other GSM phones; to query balance or activate some service. Tried forums but no concrete solution.
View 1 Replies
View Related
Aug 11, 2011
Any use the Motorola Date and Time Widget? Mine seems to hang at night (seemingly about 20min after I plug it in for charging) and stays on yesterdays date and time until somehow it corrects itself the next day. There is no way to "activate it" or make it correct itself. All other clocks and calendars are correct.
View 15 Replies
View Related
Jan 23, 2012
I have a Sprint Motorola Photon 4G and I am using it in Brazil with a Claro SIM Card. The phone reboots itself sometimes when I try to make or receive a phone call (2 or 3 times a day). I know this is happening to other Photon owners and I already tried the factory reset twice. My build # is 4.5.1A-1_SUN-198_6. Does anyone know a fix for that?
View 15 Replies
View Related
Oct 12, 2011
i bought a photon at best buy today, carried it around for a while, installed the netflix app, brought it home, plugged it in, and after i tell it to install the system update, it downloads, i click install, and it shuts down immediately, starts itself back up, and then as soon as everything comes back up, i get a message that says update has failed. this has happened 3 times now, downloaded on wi-fi
View 12 Replies
View Related
Sep 19, 2011
That's basically it. I don't want to keep getting e-mail (at my gmail account) that I have no events on a given day. How do I stop the Photon calender app from doing this?
View 4 Replies
View Related
Jan 9, 2012
I have a major issue with my corporate exchange calendar. If I accept an invitation to a meeting, the phone makes me the organizer of the meeting. This syncs back to my corporate calendar. This is obviously completely wrong. If I delete the meeting on my phone, or on my computer, it sends out a message to everyone that was on the meeting saying that it was cancelled. If I need to adjust the meeting only on my calendar, it sends out an update to everyone. It has caused a lot of confusion for me and my work colleagues.
View 3 Replies
View Related