BB Storm :: Unable To Set The Number Of Rings On Incoming Phone Calls?
Jan 31, 2011
I am unable to set the number of rings on incoming phone calls. I can adjust the count for vibration, but no "count" icon is available in the ring tone section.
When my phone rings while incoming calls, I am niether recieve income calls nor disconnect it, the whole screen hangs off n tapping of any where on the sscreen dosen't work.
I have set up my Curve 8360 but I cannot adjust the number of rings of the actual phone as I can for other notifiers. I have seen the message in the Blackberry manual that says that this might be controlled by the provider - in this case Vodafone. I have contacted them but they say they have no control over this. They can provide me with a code to extend the time before it goes to voicemail but it does not affect the number of rings. I can amend the volume and I have control over the vibration and LED but I can't change the number of rings from the current 1.
Been a happy Sprint user since 2005 and have used various dumb phones and smartphones. The Photon is my 3rd Android.I have noticed that each phone , whether smartphone or not, has the same issue that has caused me to miss incoming phone calls here and there - the caller dials my number and hears several rings before my phone actually starts ringing. The phone goes to voicemail before I have the opportunity to answer the phone.The solution for my phones has always been to adjust the Slot Cycle index from the default setting of 2 to the setting of 0. This causes the phone to poll towers more frequently, thus the phone is more quickly aware of a new incoming call. The only negative implication is that the phone goes through battery a bit more quickly during the day...but it's really only a tiny difference. I've done this on my phones, on my spouse's phones, my mom's phone, etc.
Since the Photon's battery life is so much better than my prior phone (EVO 4G) I am very comfortable in adjusting the Slot Cycle index, so I obtained my MSL from Sprint and attempted the adjustment by going to the Dialer:##DATA# ->tap green Dial icon -> to the Data Settings menu...tap Advanced->From there you can see that the Slotted Index is set to 2. So I wanted to change the setting but can't get to it from Menu->Edit->enter MSL code->VerifyI called Sprint about this issue, and in the past they have helped me to change the setting. I have called more than once and have been dealing with the more advanced Tech Support team. No one at Sprint can figure out how to adjust this setting on the Photon.
I had an 8 month old phone that was actingup , going to speaker phone with no buttons being pushed , couldnt answer incoming calls, couldnt see who was calling . Yesterday i had it swapped out for a new refurbished unit and it is doing the same thing today . Has anyone heard of or experienced any of these problems
My phone rings twice then cuts out on the 3rd. I have had extensive e-mail conversations with support staff to no avail. Initially they gave me numbers to input but that did not work. Then, on 2 occasions, the support staff did the work themselves, but my phone continues to cut out early. how to increase the number of rings?
How do i set up the number of rings on my phone, before it goes to voicemail ? Can't find this in instruction book, or voicemail prompts on phone. My carrier is AT&T. Thanks for any help.
I am using Blackberry Storm2 9550. The problem is these days when ever am getting a call the country name is not being displayed on the screen, previously it was comming but since am facing this problem.
After certain time in the phone all incoming calls show the same number in caller ID.The number that is shown will be the last call received before the problem starts.The call log shows the correct number but when call is received the same number is shown.This continues till the phone is reset. But it reverts back to the same issue after some time.I thought this was a problem with the phone and changed Handset and SIM card also, but still the problem came back after a couple of months. My service provider is not able to help me. I tried updating the software in the old phone but still the problem was there.This is driving me crazy since there are many calls I dont want to attend.
I am using Blackberryr 9300. I bought it last month and it was working fine. From past week incorrect information is displayed on all incoming calls(Eg : for every caller it would show up the last dialled call details, sometimes it just displays few digits etc).
Ok I have a new problem which I think was caused by me accidentally deleting my email live tile I could not find how to replace the tile it was only tonight that I realised that it was listed as linked inbox!
anyway the only way I could see to replace the tile was to remove and add my email accounts.
Now when I get a call I get the incoming number but not the name and if I look in the call history there is just the number, when I look later it has the name displayed.
Why the names are not being displayed, I am tempted to do a full reset but my 920 bricked when I did it and it is not back from repair yet so I am scarred to do it on my 1020.
When I receive a call it will come up on the phone as either the last number received or a random collection of numbers. quite often in one day I will receive 20 calls and all incoming calls on that day will be the same number until i answer the call. Any ideas?
I have an Iphone 4 and I just changed my number. After changing it ( last weekend) my phone has not let me receive or send texts or calls. Also, when I go to message settings on my phone my old number is still there and idk how to put in my new one. I have already tried resetting network settings. but that hasn't worked....
I bought an unlocked Iphone 4s from apple in CA and moved to Bangalore. I have a local sim setup and phone works fine, except that all incoming calls are marked as "unknown".