My phone wont reset to factory conditions. Some things are returne to stock, but many of my settings remain the same. Phone is sluggish and for example the icons under messaging take several seconds to appear. I want to reset the phone to the basic stock setup as when the phone was new.
My Defy kept restarting approximately 5 seconds after starting up. Without being able to access any settings I tried a factory reset via the on button / volume down button. I'm not sure how long this should have taken but decided after a few hours of nothing more than a yellow dot moving across the screen that it wasn't working. Button presses / screen taps had no affect so I pulled the battery.On powering it up it now either gets as far as the Moto Blur or T-Mobile logos but just hangs there. Further attempts to factory reset give the same result as the first time.I've noticed two lines of text when accessing the reset screen which read 'E:Can't open /cache/recovery/command' and 'E:Can't open /cache/recovery/caller'. I think these were present at the first attempt but I'm not totally sure of this.In cast it's relevant the phone shipped with Eclair, I changed this to Froyo using the Motorola software upgrade some months ago, it had been working fine since apart from not saving photos (?).
I dropped my phone earlier today and my phone went blank. When I tried to restart the phone, I noticed that the screen was really dark and that I was able to see the Motorola logo when I looked at it at a certain angle. I tried looking through the forums and tried doing a factory reset but I'm unable to do so because once I get past the pressing the camera and power button step, I'm unable to see anything on the screen and it seems as if the touch screen isn't working either. I'm unable to see any options and seems like I can't press any buttons either.
2 Days Back i received a mess that i can upgrade my RAZR to ICS.Before upgrading i thought i will clean up my phone by doing a factory reset and then go for upgrade.After doing the factory reset when i checked for system update to upgrade.i am not able to do as the mess pops up saying "Your Device is up to date! No update is necessary at this time".but my android version is 2.3.6 only.I am staying in INDIA
After the update i want to restore to its original settings but when i press those buttons (power + volume down) it shows an android and ! which suppose to bring me in an options when i press the lower left of the screen but not, it doesn't work anymore
After the update to 2.2.2 and after a hard reset, the phone takes a long time syncing my Google accounts e-mails. Is there a setting that i have missed ? I am on a 3G data plan. Before when a new e-mail was received in the Gmail inbox i instantly received a notification on my phone.
I've read where people say to do a factory reset before or after installing updates. What about doing both? Anyone ever done this? Also, how long does it normally take to get the update notification AGAIN if doing a factory reset before down loading it?
I have been debating for the past couple of weeks on doing a factory reset on my phone to see if it clears some minor annoyances. Now that GB is starting to roll out, should I do one now before I get the update
After much consideration, and annoying "xxx has stopped working," I finally factory reset my phone. Wiped everything completely.. Other than Google Search which has refused to understand that I don't care what my previous searches are.. But, I need your input on :
-must have applications. -apps to disable. -anything else that is convient.
For some reason, my phone just did a factory reset. I wasn't using it, just had it in my pocket with headset plugged in. Pulled out the headset from the jack and was going to make a call. When the screen turned on there was the Android icon with what looked like a green "electron cloud" type symbol animated in its open "belly". After a few minutes with that on the display, tried to shut the phone off, it wouldn't power down so I did the volume down and power button. When it came back, the phone was cleared asking me to select a language.
I did a factory reset on my atrix today and could not log onto my blur account, both on my phone and online. On my phone, I get the error message, "An error has occurred. Please try again." Logging in online, I get the message, "There was an internal error. Please try again later." I have search on the fourms and found no definitive answers. Live chat was no help either. I would rather not have to create a new motoblur account.
Assume my Droid is working, and it goes to sleep after a period of disuse, or a click on the power button to put it to sleep. Then, when I click the power to turn it back on, the screen appears but none of the controls work. When I swipe the unlock icons, nothing happens. Nothing happens when any button is pressed or any screen item is pressed.If I merely pull the battery nothing works.If I pull the battery and then do a hard reset, using the X plus power kay, then a reset, the phone will work fine...until it goes to sleep, when it freezes again and the only way to revive it is to do another hard reset.I did a hard reset, and cleared all of my user data...but still the phone froze after it went to sleep.This happens whether or not the 16 GB data chip is pulled.It happens with a fully charged battery as well as using the power cord.Finally, I did a factory reset and wiped out everything, so that I was starting with a new default system and a new activation.The phone started up fine...and I could access the factory-installed apps...but when it went to sleep it froze again. When I tried to wake it I could not get by the home screen.I had this problem starting a few days ago. Then it seemed to go away. Then a day later it started again.Why does going to sleep kill a phone that otherwise works perfectly?It can't be any add on apps, because there are none.
I bought a used DROID X from a friend to use only with Wi-Fi, not with Verizon service. It worked fine with only Wi-Fi even though it had no service. I did a Factory Reset to wipe it clean. Now when it comes up it goes to the activation screen and will not go past it, forcing activation to continue. I do not wish to activate the phone with Verizon, only use it with Wi-Fi. Does anyone know how I can get the phone back to working with Wi-Fi only? Is there an Android ROM version I can download from somewhere and load on this phone so that it does not force activation?
did a factory reset due to the market kept insisting I had updates, and when I go to maket none were available. And I got tired of doing this So I did the factory reset. This is the second time I have done this task. Last time it was a breeze, and once done all the apps I had prior automatically re-downloaded of their own. Didn't happen this time, and that is no biggy,But what is bothering me is I still have the old version of the market. At least it works, but it has been a little over 24 hours since I did the reset...shouldnt the latest version of market been made available to me by now?
When I owned my Droid X, I remember seeing a lot of people saying that after GB was installed, they recommended doing a factory reset.I never did this, and felt like the phone did fine, but of course got a little slower with age. love my Maxx and was wondering if anyone still recommends doing a FDR after installing ICS?It's nearly brand new, so doing a reset wouldn't be much of a hassle for me since I don't have much on the phone right now.
I performed a factory reset today to remove MySpace from my phone (I was unable to remove it any other way) and now I am having an issue with my phone.A number of my notification icons are now showing in gray instead of in color. The two that stand out the most are email notifications from POP emails (the red stamp) and from Gmail. Each of these now shows as a gray icon. This is minor, but annoying that my phone is behaving differently than it should. I am running 2.3.4 and have tried multiple resets (full resets removing all data and media)
Do you think if I do a factory reset BEFORE installing the latest update that may help 'clear' out the few 'bugs'? ie, cannot even get the indoor calibration anywhere near close to what it should be also, I think mine has an issue with the screen timeout function and a few other things.
I was wondering (since I have a few things on my MA that are not working correctly)...Do you think if I do a factory reset BEFORE installing the latest update that may help 'clear' out the few 'bugs'? ie..cannot even get the indoor calibration anywhere near close to what it should be...also, I think mine has an issue with the screen timeout function..and a few other things..Now, if i DO a reset before installing...After the reset, when I connect my MA to my computer, will it prompt me to go to the most current update or not?For the last update, I just connected and everything was fine.....I'm not that great with computers and I would NOT want to turn this into a Customer Service issue -- if you know what I mean...